Source: Fixr, rubber roof cost guide, updated January 31, 2025. Seams from This Old House, TPO roofing guide, updated November 12, 2026.
PVC vs. TPO roof is the closest call in flat roofing. Both are white single-ply membranes, both come in wide rolls, and both have seams that are welded with hot air rather than glued. The differences are in the chemistry and the track record: PVC is a vinyl membrane that has been on roofs for decades, while TPO is a newer blend of rubber and polypropylene that This Old House calls slightly stronger. PVC usually costs a little more.
This guide compares the two side by side: how each is made, cost, lifespan, how they handle heat, hail and grease, and how to tell which one belongs on your building. For how we inspect and quote flat and low-slope roofs, see our commercial roofing page.
In this guide
- PVC vs. TPO at a glance
- How PVC and TPO are made
- Cost and lifespan
- Heat, hail and the Texas sun
- Grease, chemicals and rooftop equipment
- Installation and repairs
- Which one fits your building
- PVC vs. TPO questions
PVC vs. TPO at a glance
| Feature | TPO | PVC |
|---|---|---|
| Material | Thermoplastic polyolefin: synthetic rubber and polypropylene | Polyvinyl chloride (vinyl) with plasticizers for flexibility |
| Standard to ask for | ASTM D6878 | ASTM D4434 |
| Seams | Heat-welded | Heat-welded |
| Color | Usually white | Usually white |
| Installed cost | $4.50–$14 per sq ft | $5.50–$15 per sq ft |
| Typical life | 15–20 years (Fixr); 15–30 (This Old House) | Around 20 years (Fixr) |
| Track record | Relatively new | Decades of use |
Sources: This Old House, TPO roofing guide, updated November 12, 2026; Fixr, updated January 31, 2025; ASTM standards from the 2021 International Residential Code, section R905.13.
The two lifespan figures for TPO don't agree, and that is normal for flat roofs. Every range assumes a roof that was installed well and maintained. Seams, flashing and foot traffic decide where a real roof lands far more than the brand name on the sheet.
How PVC and TPO are made
TPO
TPO is a blend of synthetic rubber and polypropylene. Reinforced sheets have a polyester scrim sealed inside for strength. The material is thermoplastic, which means it softens when heated and hardens as it cools, so two sheets can be welded into one. Our guide to what a TPO roof is covers thickness (45 and 60 mil are common) and how the membrane goes on.
PVC
PVC is also thermoplastic and also reinforced. This Old House describes it as two layers with a polyester scrim between them: the top layer carries UV-resistant additives, and the bottom layer carries plasticizers that keep the sheet flexible and easier to install. Those plasticizers are the main chemical difference between the two. TPO gets its flexibility from its rubber content instead.
Because both are thermoplastic, both are installed the same basic way and both are repaired by welding a patch of matching membrane over a cleaned spot.

Cost and lifespan
Fixr's cost guide puts TPO at $4.50 to $14 per square foot installed and PVC at $5.50 to $15. Both ranges are wide because a membrane price includes far more than the sheet: tear-off, replacing wet insulation, new cover board, the attachment method and every wall, curb, drain and pipe that needs flashing. On a typical flat roof the details, not the membrane, are what move a bid.
This Old House's November 2026 flat roof guide prices TPO at $8 to $11 per square foot on a 2,000-square-foot roof and doesn't price PVC. So when two quotes are a few thousand dollars apart, check that they cover the same thickness, the same insulation and the same flashing scope before reading anything into the membrane choice. Our commercial roofing types guide shows how both compare with EPDM, built-up and metal roofs.
On lifespan, Fixr gives TPO 15 to 20 years and PVC about 20, noting PVC tends to need repairs after about 10 years. This Old House gives TPO 15 to 30 years with regular maintenance. PVC's real advantage here is history: there are many more old PVC roofs to learn from.
Heat, hail and the Texas sun
Both membranes are usually white, and on a Texas flat roof that matters. The EPA lists light-colored single-ply membranes among the low-slope cool roof options and says a cool roof can cut peak cooling demand in air-conditioned buildings by 11 to 27 percent. Neither PVC nor TPO has a clear edge here. A white sheet of either reflects far more sun than a black one, and either loses some of that as it gets dirty.
Hail is the bigger Texas question. Texas had 902 major hail events in 2025, more than any other state, according to the Insurance Information Institute. A single ply can be punctured by large hail, foot traffic or dropped tools on either membrane. Membrane thickness and what sits under it affect how a roof takes a hit, and so does looking at the roof after every big storm rather than waiting for a ceiling stain.
Grease, chemicals and rooftop equipment
What lands on the roof can matter more than the climate. This Old House notes TPO resists oil and grease. Buildings with kitchen exhaust, oily equipment or chemical vents should get the specific product's chemical-resistance information from the manufacturer before choosing, because results vary by product and by the chemical involved.
Rooftop units bring service visits, and service visits bring boots, tools and dropped screws. Fixr lists PVC as handling heavy foot traffic. On either membrane, walkway pads along the paths technicians actually take are cheap protection.
Installation and repairs
The install steps are close to identical:
- Tear-off and deck check. The old roof comes off and any wet insulation or soft decking is replaced.
- Insulation and cover board. Rigid board goes over the deck to give the membrane a smooth, dry base.
- Membrane. The sheets are rolled out with overlapping laps and fastened or adhered.
- Welded seams. A hot-air welder fuses each overlap. A weld that was rushed or run too cool is where leaks start.
- Flashing. Walls, curbs, drains, pipes and edges get membrane flashing welded to the field sheet. Our roof flashing installation guide explains why these details fail on any roof.
Fixr notes PVC repairs should be done in warm weather. Texas gives plenty of that, but a cold snap can push a PVC repair back a few days.

Which one fits your building
- Lowest first cost on a simple roof: TPO, whose installed range in Fixr's guide starts lower.
- A longer track record: PVC, which has been on roofs for decades.
- Kitchen exhaust or chemicals on the roof: ask for the manufacturer's chemical-resistance data for the exact product on each bid.
- Heavy service traffic: either, with walkway pads, and a thicker sheet if the budget allows.
- Repairing what is already there: match the existing membrane. TPO welds to TPO and PVC to PVC, so knowing what you have is the first step.
If you aren't sure which membrane is on your roof now, an inspection will tell you. That answer decides whether a repair is a simple welded patch or a bigger job.
How we look at a flat roof
Viva Roofing is a family-owned roofing company with an office in Frisco, working across Dallas-Fort Worth, San Antonio and Austin since 2021. Most of our work is residential, and we also take on flat sections, small commercial buildings and multi-family properties. On a low-slope roof we:
- Inspect and photograph it. The field, the seams, the edges and flashing, drains and every penetration, with drone photos where the building allows. You keep the photos whether or not you hire us.
- Look for a repair first. A sound membrane with a few failed welds can often be patched.
- Quote options in writing. When the roof needs replacing, we explain which low-slope option fits the building and why.
We inspect flat and mixed roofs from Frisco, Allen and Rockwall to New Braunfels and Round Rock. To settle PVC vs. TPO for your own roof, see our commercial roofing page or request a free inspection.
PVC vs. TPO questions
What is the difference between a PVC and a TPO roof?
Both are white, heat-welded single-ply membranes. PVC is a vinyl sheet made flexible with plasticizers and has been on roofs for decades; TPO is a newer blend of synthetic rubber and polypropylene that This Old House calls slightly stronger. PVC usually costs a little more.
Which is cheaper, PVC or TPO?
TPO, usually. Fixr puts TPO at $4.50 to $14 per square foot installed and PVC at $5.50 to $15. Tear-off, wet insulation, thickness and flashing details often move a bid more than the membrane choice does.
Does PVC or TPO last longer?
Fixr gives PVC about 20 years and TPO 15 to 20, while This Old House gives TPO 15 to 30 with maintenance. Installation quality, especially the welded seams and flashing, decides where a real roof lands.
Is PVC or TPO better for a restaurant roof?
This Old House notes TPO resists oil and grease. For kitchen exhaust or chemical vents, ask for the manufacturer's chemical-resistance data for the exact product on each bid, because results vary by product.
Can you weld TPO to PVC?
No. The two are different plastics, so a repair has to match the existing membrane: TPO patches on TPO and PVC on PVC. Knowing which one is on your roof is the first step of any repair.
Are PVC and TPO roofs good in Texas heat?
Both are usually white, and the EPA lists light-colored single-ply membranes among the cool roof options that can cut peak cooling demand by 11 to 27 percent. Keeping the surface clean keeps more of that reflectance.